User Tools

Site Tools


howtovoip:start

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

howtovoip:start [2020/04/17 12:07] (current)
support created
Line 1: Line 1:
 +\\ 
 +===== Voip ===== 
 +\\ 
 +\\ 
 +**__Question:​__** How to use the Voip channel in my mixer?\\ 
 +\\ 
 +**__Answer:​__** [[howtovoip:​start|please follow the steps at this link]]\\ 
 +\\ 
 +\\ 
 +------ 
 +\\ 
 +=====Introduction===== 
 +\\ 
 +The Voip channel is actually a USB sound card with the advantage of having a Mix minus 1 (N-1) and Clean feed output.\\ 
 +The Mix minus 1 prevents the caller from hearing his self by sending back the Mix minus itself (1). 
 +The Clean feed output does the same by sending out the Mix minus itself for the Line input at that channel.\\ 
 +This can be used to connect an external Hybrid like the Hybrid 1, 2 or GSM Hybrid.\\ 
 +\\ 
 +Our Voip channel are based on the CM119 USB sound card.\\ 
 +As all the Voip channels work the same way I will call them Voip channel in the instructions.\\ 
 +\\ 
 +\\ 
 +------ 
 +\\ 
 +===== Voip channels are available for ===== 
 +\\ 
 +=== Airlite === 
 +\\ 
 +The Voip channel can be found (blue at the picture) at channel 8.\\ 
 +\\ 
 +{{:​howtovoip:​airlite_front_2.png?​400|}} 
 +{{:​howtovoip:​airlite_backpanel.jpg?​400|}} 
 +\\ 
 +\\ 
 +=== Webstation === 
 +\\ 
 +The Voip channel can be found (blue at the picture) at channel 6.\\ 
 +\\ 
 +{{:​howtovoip:​webstation_front.png?​400|}} 
 +{{:​howtovoip:​webstation_backpanel.png?​400|}} 
 +\\ 
 +\\ 
 +=== Airmate 8 and 12 === 
 +\\ 
 +The front (blue at the picture) is the same as with a telco, it can be recognized at the backpanel by the USB connector.\\ 
 +\\ 
 +{{:​howtovoip:​airmate-usb.jpg?​400|}} 
 +{{:​howtovoip:​airmate-usb_backpanel.png?​400|}} 
 +\\ 
 +\\ 
 +=== Airence Main === 
 +\\ 
 +The front (blue at the picture) is the same as with a telco, it can be recognized at the backpanel by the USB connector.\\ 
 +\\ 
 +{{:​howtovoip:​airence_front.jpg?​400|}} 
 +{{:​howtovoip:​airence_backpanel.jpg?​400|}} 
 +\\ 
 +\\ 
 +=== Airlab === 
 +\\ 
 +The front is the same as with a telco, it can be recognized at the backpanel by the USB connector.\\ 
 +\\ 
 +{{:​howtovoip:​airlab2.jpg?​40|}} 
 +{{:​howtovoip:​airlab_voip.jpg?​40|}} 
 +\\ 
 +\\ 
 +----- 
 +\\ 
 +=====How can I configure the VOIPchannel with a VOIP application?​===== 
 +\\ 
 +To use the Voip channel you'll need a Voip application on your computer and you need to setup the application to use the Voip channels "​Microphone"​ input and "​Loudspeaker"​ output.\\ 
 +\\ 
 +Download Skype or another Voip application and install it on your PC.\\ 
 +\\ 
 +When you connect the USB cable from your Voip channel to your PC, your operating system will see for example the "​Airlite VOIP" audio codec and install it as a "​Microphone"​ and "​Loudspeaker"​.\\ 
 +\\ 
 +Since most Voip applications need a "​Microphone"​ input to use for the incomming sound we used the CM119 chip.\\ 
 +\\ 
 +Go to the settings of your Voip application and configure the commmunication Microphone and Headphone as the Voip channel source instead of the default Microphone and loudspeaker of the PC.\\ 
 +\\ 
 +More information about how to configure your application can find the manual of the Voip application.\\ 
 +\\ 
 +If this is done your Voip software recognizes the Voip channel as a headset and will work with all it's audio features.\\ 
 +\\ 
 +It is possible to answer and make outgoing calls by opperating the computer but we also added a connect button and signalling feature.\\ 
 +\\ 
 +\\ 
 +---- 
 +\\ 
 +=====Using the VOIP connect button:​===== 
 +\\ 
 +\\ 
 +To use the Connect button you'll need the D&R Voip connect application which can be found on the product support and software website.\\ 
 +\\ 
 +For the Airlite the firmware needs to be version 1.20 or higher to be able to use this application.\\ 
 +You can find which firmware version is installed in the Airlite Configuration manager after you press Read.\\ 
 +\\ 
 +Download and install this application.\\ 
 +\\ 
 +{{:​howtovoip:​voipconnect1.jpg?​200|}} 
 +\\ 
 +When installed the application starts as a "​Service"​ can be found at the taskbar.\\ 
 +\\ 
 +{{:​howtovoip:​voipconnect2.jpg?​200|}} 
 +\\ 
 +When you right click on the icon and press Settings it will open the configuration of the D&R Voip connect application.\\ 
 +\\ 
 +{{:​howtovoip:​voipconnect3.jpg?​600|}} 
 +\\ 
 +Select the model of the Mixing console that you are using.\\ 
 +\\ 
 +This application works like a virtual keyboard mapper for most Voip applications.\\ 
 +\\ 
 +So when you can "​Answer"​ a call of your Voip application with a keyboard command combination and you can "Hang up" a call of your Voip application with a (different) keyboard command combination,​ you can configure these keyboard command combinations in the D&R Voip connect application.\\ 
 +\\ 
 +Simple translate the keyboard command combinations to the ones in the pulldown setting boxes.\\ 
 +\\ 
 +The connect LED setting works for the LED at the Connect switch and for the "​Start"​ jack or "​GPO"​ that is configured as Ring signalling.\\ 
 +\\ 
 +When set to "​Internal state" both will toggle between "​Off"​ and "On with each press of the Connect button.\\ 
 +\\ 
 +Now you are able to Answer and hangup a call with the Connect button.\\ 
 +\\ 
 +\\ 
 +------ 
 +\\ 
 +=====Control the Connect LED when application fires a command prompt command===== 
 +\\ 
 +To control the connect LED on the voip channel you’ll have to select “Remote Controlled UDP (Phoner app)” can fire 
 +a command with your voip software.\\ 
 +"Voip Connect"​ -s incoming\\ 
 +"Voip Connect"​ -s connected\\ 
 +"Voip Connect"​ -s disconnected\\ 
 +\\ 
 +or\\ 
 +\\ 
 +c:\Program Files (x86)\D&​R Voip Connect\Voip Connect.exe -s incoming\\ 
 +c:\Program Files (x86)\D&​R Voip Connect\Voip Connect.exe -s connected\\ 
 +c:\Program Files (x86)\D&​R Voip Connect\Voip Connect.exe -s disconnected\\ 
 +\\ 
 +These instructions can be added in a batch file which can be started in a hidden situation.\\ 
 +\\ 
 +The VOIP led of the button can be set to internal state of the switch, or  controlled ​ by the VOIP application (UDP).\\ 
 +Right mouseclick on the  blue voipconnect icon that you can find in your hidden ​ icons right under your screen to change settings.\\ 
 +\\ 
 +\\ 
 +------ 
 +\\ 
 +\\ 
 +If you still have questions about the Voip channel after these steps fill in the support contact form. 
 +\\ 
 +[[https://​www.d-r.nl/​support-request.html|Support Request]]\\ 
 +\\ 
 +Go back to the [[SupAirence:​start|Airence]] support page.\\ 
 +\\ 
 +Go back to the [[SupAirlab:​start|Airlab]] support page.\\ 
 +\\ 
 +Go back to the [[SupAirlite:​start|Airlite]] support page.\\ 
 +\\ 
 +Go back to the [[SupWebstation:​start|Webstation]] support page.\\ 
 +\\ 
 +Go back to the [[SupGSMHybrid:​start|GSM Hybrid]] support page.\\ 
 +\\ 
 +\\
howtovoip/start.txt · Last modified: 2020/04/17 12:07 by support